Please wait while the page loads...

How many miles can you drive with the check engine light?

It could be anything from a bad sensor to plug wires needing to be replaced. If you check engine light is blinking, we endorse that you pull over and contact Nalley Toyota Stonecrest to assist determine if your vehicle is protected to drive in or if we endorse a tow truck. The safest bet is to decipher the code and then plan your strategy accordingly. Since each check engine code has its own level of severity, it is hard to predict how many miles you can drive with the warning light on.

Will the check engine light reset itself?

The check engine light on your 2018 Toyota Tacoma will commonly shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going functional, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2018 Toyota Tacoma light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Nalley Toyota Stonecrest so the light and code can be double-checked and reset.

Check Engine Light Service 2018 Toyota Tacoma

What do you do when you’re driving along in your Toyota Tacoma and immediately, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Toyota owners, your heart sinks a meager because you have meager idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your 2018 Toyota Tacoma checked as soon as likely. Ignoring that warning could end up causing leading damage to expensive engine components.

When your 2018 Toyota Tacoma's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t accurate, a computer turns on your check engine light. This amber or yellow light is naturally labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is read with an electrical scan tool that is used by our Toyota auto repair mechanics at Nalley Toyota Stonecrest. There are also a number of rather low-cost code readers that are designed for do-it-yourselfers, should you pick that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an effective professional to determine the issue and repair it.

Is it safe to drive your 2018 Toyota Tacoma with the check engine light on?

This question is not highly cordial because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be safe to drive. This is commonly indicated by a steady glow of the check engine light. If you notice a difference in the performance of the car, it could be an indication of a more strict problem. If the check engine light is flashing, this means that there is a strict issue and it is recommended to service your Toyota Tacoma immediately. Call the advisors at Nalley Toyota Stonecrest by dialing 7706290279 so you can describe the issues. Or reduce your speed and bring your 2018 Toyota to our certified mechanics as soon as feasible.

2018 Toyota Tacoma Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that tiny light on your vehicle’s dashboard suddenly lights up, but in reality, it is not something that should cause you to shut down in fear right away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also known as the OBD (on-board computer diagnostic system) in your Tacoma. There are hundreds of diverse codes that your check engine light can represent. While that sounds daunting, with a tiny patience, tackling critical diagnostics will give you convenient knowledge about your vehicle and will also allow that Check Engine Light to do what it is really supposed to do: be your guide. Unfortunately, accessible and cooperative vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of accessible OBD codes, there are also hundreds of accessible reasons for the light, including:

  • Ignition system faults
  • Computer output circuit issues
  • O2 Sensor
  • Emissions controls issues
  • Bad Spark Plugs
  • Old Battery
  • Loose Gas Cap or Missing Gas Cap
  • Transmission issues
  • Fuel and air metering systems problems

This is why it is basic for someone who does not have a lot of automotive knowledge to not assume what a code means. Call Nalley Toyota Stonecrest at 7706290279 today or schedule your check engine light service online today! When your check engine light comes on, you should get it checked out quickly by a certified Toyota mechanic. If the engine light comes on due to a relentless concern, you risk damaging your car extra by not repairing the issue right away.

How much does it cost to get the engine light checked?

The check engine light warns of issues ranging from a gas cap that's not appropriately tightened to a more relentless failure like a harmful catalytic converter or a problem with one of the car's oxygen sensors, so it excellent to get the suitable code reading and diagnosis. The average cost for a check engine light diagnosis & testing is typically between $88 and $111. The excellent news, Nalley Toyota Stonecrest offers complimentary multi-point inspections and free diagnostics, in most cases, to help suggest the cause of your check engine light.

What could cause the check engine light to come on in a 2018 Toyota Tacoma?

When your check engine light comes on, this could be as classic as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a severe problem that could cause severe damage to your engine and come with a major repair bill. Depending on your make and model, the check engine light will illuminate or blink. A persistent glow naturally means something less severe but a blinking check engine light expresses that your vehicle’s engine is in severe trouble and service is needed at this moment. If your check engine light is blinking in your 2018 Toyota Tacoma, we hugely hint not to drive the vehicle and schedule Toyota service today. Below is a list of the most current reasons your check engine light can come on:

  • Your catalytic converter is bad or going bad. The catalytic converter is a part of your 2018 Toyota Tacoma’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is usually caused by neglected maintenance, which is why Nalley Toyota Stonecrest offers a complimentary multi-point inspection with every Toyota service. If you have an issue with your catalytic converter and don't get it repaired, your 2018 Toyota Tacoma will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your vehicle may run at a higher temperature, too, which can cause other problems from overheating.
  • New Spark Plugs or Plug Wires are needed for your 2018 Toyota Tacoma. The spark plugs are the part of your engine that ignites the air/fuel mixture in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or old, you will experience poor performance and reduced power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, dominant to more expensive repairs.
  • The battery is low or dead. The battery in your 2018 Toyota Tacoma is every crucial. Without a vehicle battery, your vehicle won’t start, light up the road ahead, play the radio or charge your phone. Today’s vehicle batteries last much longer than they did a few decades ago, and they don't absolutely require maintenance. The price of a new one depends on the type of Toyota you drive, but check our ongoing service coupons and specials.
  • Your 2018 Toyota Tacoma has a vacuum leak. Every Toyota Tacoma has a vacuum system that performs a wide assortment of functions. The vacuum system also helps lower contentious emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, exceptionally if they’re exposed to profound heat or extreme bitter.
  • One of the most aware and frequent cause is that your 2018 Toyota Tacoma gas cap is loose, damaged or missing. The gas cap for your 2018 Toyota Tacoma serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is old or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on immediately after you put gas in your 2018 Toyota Tacoma, first thing you should check is to make hopeful the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or other item can wreak havoc on your 2018 Toyota Tacoma if it’s not installed perfectly. These aftermarket parts and accessories can ditch the battery, trigger the check engine light, or even prevent the vehicle from starting. If these issues sound aware, bring your Tacoma to Toyota and have our unit of certified mechanics ensure that your aftermarket items were installed accordingly and aren't causing any issue. Getting accessories, exceptionally aftermarket parts and accessories, or using OEM parts first place might cost a little bit more but could save you money from having to get poor work and damage caused by poor installation work corrected.
  • Your O2 Sensor (Oxygen Sensor) needs to be replenished. The Oxygen sensor, known as the O2 sensor, measures the sum of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be fewer practical when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your 2018 Toyota Tacoma's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to pick the right mixture of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a vehicle to fail an emissions test.
  • Your mass airflow sensor (known as MAF) needs to be replenished. The mass airflow sensor in your Toyota Tacoma is what determines how much fuel is needed to run your engine efficiently by measuring the sum of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to accurate changes, like altitude. If your Toyota Tacoma is having trouble starting, idling rough or has a sudden change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.

2018 Toyota Tacoma Check Engine Light

A flashing light hints that the problem is dangerous and if not taken care of instantly may result in major damage to the car. If the check engine light in your 2018 Toyota Tacoma starts flashing, that means that the problem needs immediate attention and your Toyota should be brought in instantly. This blinking light usually indicates a harsh engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can swiftly hike the temperature of the catalytic converter to a point where damage is likely, requiring an expensive repair. Some owners ask if spark plugs cause the check engine light to flash? This can precisely be the cause. A damaging, long-established or dirty spark plug can cause the engine to misfire. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a exceptionally fancy repair. If your check engine light is flashing, please contact our squad of automotive experts at Nalley Toyota Stonecrest immediately by calling 7706290279.

2018 Toyota Tacoma Check Engine Light Flashing

Although there are copious attainable causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are a lot intelligent causes including something as plain as a loose gas cap. Disparate intelligent reasons for a Check Engine Light are damaged oxygen sensor, dirty mass airflow sensor, faulty head gasket, faulty emissions control part, a malfunction with the fuel injection system, or defective spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Toyota Certified Technicians and the certified service protocol to isolate the root problem and repair it as fundamental to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Toyota issue was revamped.

Every 2018 Toyota Tacoma was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its critical systems. The sensors are continually detecting conditions while sending data to the electronic control unit. If the electronic control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what definitely is untrue nor what to do about it. That’s where we come in; Nalley Toyota Stonecrest provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Exceptionally Qualified Service experienced.

What Does the Check Engine Light Mean?

One of the most typically misunderstood lights or indicators in your 2018 Toyota Tacoma is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in a few odd ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a assortment of things for your 2018 Toyota Tacoma. Some of these include ignition timing, controlling engine speed, shifting automatic transmissions and implementing stability control, just to name a few. With that being said, the check engine light can imply a variety of distinct things. It can be as straightforward as your gas cap being loose or as perilous as engine knocking. If your check engine light is on in your 2018 Toyota Tacoma, contact Nalley Toyota Stonecrest. Contact Nalley Toyota Stonecrest today! Our Toyota service department can help you find out what code is turning your check engine light on or diagnose why your check engine light is shining.